Kineis

Supported technology/Animal Tracking

kineis.com/en/spatial-iot-connectivity

Direction Data provider
Data Movement data
Type Pull integration

Setup You, in the portal

Kineis sends satellite positions (GPS and Doppler) to EarthRanger through Gundi. Gundi checks your Kineis account on a schedule, and the positions show up as tracks on the map.

What you'll receive

We add details here as we confirm what Kineis sends. If you know something we're missing, let us know.

Positions Yes, from every device on your Kineis account, unless you list specific devices in Device refs or Device UIDs. Each position says whether it is GPS or Doppler, with a confidence level and, for Doppler, an error radius. Doppler positions are sent once they settle, 6 hours after the fix by default (Doppler settle hours). Messages without a location are skipped.
Alerts and events No
Sensor readings The full Kineis message is included as it arrives, so its contents depend on your device.
Photos and files No
Past data Yes. A daily catch-up run re-reads the last 48 hours; you can set 1 to 168 hours with Lookback hours. For older data, see "How can I process historic data?" below.

How this integration works

This is a pull integration. Gundi checks the data provider for new data on a schedule, using the account details you enter in the Route, and passes what it finds on to your destination.

Who's involved

  • You create the Route in Gundi and enter your provider account details, or give them to Gundi support when the setup badge says so.
  • The data provider keeps your account and devices active.
  • Your destination, for example EarthRanger, is where the data shows up.
  • Gundi support helps only when the setup badge at the top of this page says so.

Historical data

When you first connect, Gundi fetches a limited amount of past data. How far back it goes depends on the integration and is shown under "Past data" above.

When data doesn't show up

Check your Route Activity Logs first: wrong account details and provider outages show up there. Then check with the provider that your devices are reporting.

How often data arrives

Gundi checks on a schedule. Where we know how often, it's shown under "Data Pull Frequency" on this page. New data arrives after the next check, plus the time the device takes to upload it to the provider.

Prerequisites

Kineis

You will need:

  • An account with them.

EarthRanger

To send movement data to EarthRanger, you will need:

  • A special EarthRanger user (e.g., “Gundi Service Account”) for this integration. Please refer to EarthRanger's documentation or contact Support.
  • A long-lived token for authentication assigned to the user created in the previous step. Please refer to EarthRanger's documentation or contact Support.

Configuration

GUIDES

I. Gundi Connection Settings

1. Login to Gundi.

2. Click on Create Route.

3. Select Kineis.

4. Select your Workspace.

5. Enter a name for this Route (e.g., “Kineis - AccountName”).

6. Configure your Account details (username, password).

7. Leave everything else with their default values or empty.

9. Click Next.

10. Click Add destination on the flow map and select a destination. Please consult our guide.


Troubleshooting

Is there a difference in the number of records between Keineis (portal) and EarthRanger?

Our integration only uses records with a location, and skips duplicated entries (same timestamp, latitude, and longitude). Please contact our team if you believe there are other reasons behind the mismatch.

How can I process historic data?

  1. In Gundi, navigate to the connection and click on the “Provider” tab. 
  2. Switch off “Use realtime API” 
  3. Add a device identifier in “Device Refs”. 
  4. Save your changes.
  5. Wait for the integration to run
  6. Revert your changes by switching on “Use realtime API” and removing the device from “Device Refs”.
  7. Save your changes.

Data Pull Frequency

Approximately every 2 minutes.

Other Animal Tracking

Argos Africa Wildlife Tracking (AWT) Advanced Telemetry Systems (or ATS)
Ceres Wild digitanimal
Back to the integration catalog Need help setting this up? Contact us